X-Symphony

Are Apogee products compatible with Pro Tools 12?

Yes!  The following products have been tested and are fully compatible with Pro Tools 12 (every version of 12):

  • JAM
  • JAM 96k
  • MiC
  • MiC 96k
  • Groove
  • GiO
  • ONE for Mac (old and new versions)
  • ONE for iPad & Mac
  • Duet FireWire
  • Duet 2
  • Duet for iPad & Mac
  • Quartet for iPad & Mac
  • Ensemble FireWire
  • Ensemble Thunderbolt
  • Symphony I/O (USB, Symphony, and Pro Tools HD modes)
  • Symphony I/O MkII (Thunderbolt and Pro Tools HD)
  • Symphony 64 PCIe
  • Symphony 64 | ThunderBridge
  • X-Symphony equipped X-Series and Rosetta Series Converters
  • X-HD equipped X-Series and Rosetta Series Converters

Signal not showing up where it’s supposed to and routing incorrect in Pro Tools

If your signal isn’t showing up correctly in Pro Tools, coming out of Pro Tools to the desired outputs, or if the routing isn’t showing up as expected, there are a few things to check. Look below for the section that applies to the Apogee product you’re using:

 

JAM, JAM 96k, MiC, MiC 96k, Groove

  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window. If you are using JAM or MiC, you will first need to create a ‘Pro Tools Aggregate I/O’ and then you will select ‘Pro Tools Aggregate I/O’ as your ‘Playback Engine’. Click here for setting up JAM for Pro Tools.  Click here for setting up MiC for Pro Tools.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

 

ONE (every model), GiO, Duet (every model), Quartet, Ensemble (every model)

  • Confirm that you are using the correct inputs/outputs on your device. Click here for instructions on how to setup ONE.  Click here for instructions on how to setup Duet.  Click here for instructions on how to setup Quartet.
  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window.
  • Launch ‘Apogee Maestro’ and click the ‘Reset Routing’ button in both the ‘Input Routing’ and ‘Output Routing’ tabs. If you’re using an Avid Duet or Avid Quartet, you will use ‘Pro Tools I/O Control’ app instead of Maestro. Click here if you need to download the Pro Tools I/O Control app for Avid Duet or Quartet.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

Symphony I/O, Symphony I/O MkII, AD16x, DA16x, Rosetta 200, Rosetta 800

 

 

What is ‘VBus’ and how do you use it?

Apogee’s VBus creates virtual hardware buses to allow expanded routing of audio within one application or between different audio applications. For example, it’s possible in Logic Pro to record a submix of multiple audio tracks onto a new audio track as described below. It’s also possible to route between two audio applications by selecting a VBus output in the source application and a VBus input in the destination application.

VBus is only available in the Symphony system. You must have either a Symphony 64 PCIe or Thunderbridge and at least one Symphony I/O, AD16x, DA16x, Rosetta 800, or Rosetta 200 to use it.

 

To use VBus:

If you have a Symphony system and everything is connected and configured properly, launch ‘Apogee Maestro 2’ from your Applications folder and go to the ‘System Setup’ tab.  Go to the right-side of the window and click the drop-down menu under ‘VBus’ to select how many channels of VBus i/o you would like to use.  As soon as you engage VBus, quit all open applications and restart your Mac.

In order for VBus I/O to appear in your audio application’s I/O list as VBus In 1-2, 3-4, etc, it’s necessary to specify the use of the Symphony driver’s names in the application’s I/O list. For example in Logic Pro X, open Mix>I/O Labels and option-click on all the I/O found under the Driver’s I/O Label column.

As an example of how to use VBus, let’s record a submix of drums onto a new stereo audio track in Logic.  In Logic’s Track Mixer, set the outputs of the individual drum audio tracks to VBout 1/2.  Create two audio tracks (or one stereo track) and set their inputs to VBin 1 and VBin 2. Record-enable the new track and commence recording. The new track will record the mix of the individual drum tracks.

What is ‘SBUS’ (connecting 2 Macs together via 2 Symphony64 cards) and is it still supported?

SBUS was a functionality that was included with the original Symphony 64 PCIe release.  SBUS let you connect multiple Macs together to pass audio back and forth between them using Symphony 64 PCIe cards. Unfortunately, it was no longer supported after the release of Symphony I/O.

 

To use SBUS, you need at least 2 Macs (each Mac must be running OS version 10.5.8 or 10.6.8) and 2 Symphony 64 cards, along with at least one compatible Legacy Apogee converter (AD16x, DA16x, Rosetta800, or Rosetta200).  If you meet all these requirements and would like to use SBUS, click here to download the compatible Symphony 64 installer.

 

For a detailed description of SBUS, including how to set it up and use it, see pages 12-16 of the Symphony 64 user’s guide.

 

 

 

Using Legacy interfaces (AD16x, DA16x, Rosetta) with Symphony64 card or Thunderbridge

Click here to download the latest Symphony Installer package

 

To update

  1. If youʼre installing this release over a previously installed version of Symphony 64/Maestro 1, you should run the Symphony64 Uninstaller before updating to the current Symphony Release installer. If youʼre installing this release over a previously installed version of Symphony I/O software, you should run the Symphony Uninstaller included with the current Symphony Release installer package. If youʼve installed both versions, you should run both uninstallers.
  2. Double-click the Symphony System Software Installer and follow the instructions provided by the installation application.
  3. No firmware updates are required – the Symphony IO Firmware Updater is for Symphony I/O users only.
  4. You will be required to re-start your computer once installation is complete.

After updating – After updating, verify that the Symphony Source setting (found in the Maestro 2 > System Setup tab and Audio MIDI Setup) is set to the appropriate Port setting:

  • If interfaces are connected only to Port 1, set Source to Port 1 Chs 1-32.
  • If interfaces are connected to both Ports 1-2, set Source to Ports 1-2 chs 1-64.

New Features – Legacy interfaces

  • The “A” icon that previously appeared in the Apple Menu bar has been removed – Look in Maestro 2ʼs Toolbar System Status display for system information.
  • To distinguish between an AD16X and DA16X when the interface is set to Advanced routing mode or a Rosetta 800 and 200, the setting Device Type is provided in Maestro 2 (Device Settings tab). This ensures that audio paths displayed in the Input and Output Routing tabs correspond to the actual hardware I/O. If neither a 16X Series in Advanced routing nor a Rosetta is connected, the Device Type drop down is not displayed.

Known issues – Legacy DA16X Interface

  • When a single DA16X is connected in Advanced routing mode, it will initially appear as an AD16X. Simply choose DA16X under Maestro 2ʻs Device Settings > Device Type drop down menu for the interface to be correctly detected.
  • When using Symphony I/O and legacy interfaces together, Routing tabs may not display the proper number of inputs and outputs. To work around this issue, restart the computer.
  • The AD16X may initially be detected as a Rosetta 800. Workaround – restart the computer.

Using Legacy Apogee Interfaces with OS X Lion & Maestro 2

  • Note that at the current time, the use of only 1 Symphony 64 card is supported regardless of the interface connected.
  • When connecting legacy Apogee interfaces to a Symphony 64 PCIe card or Thunderbridge, ensure that the interfaces are connected in a supported hardware combination, as listed below. With a Symphony 64 PCIe card or Thunderbridge, itʼs possible to connect one supported combination to each port.
  • When connecting both Symphony I/Os and legacy Apogee interfaces to a Symphony 64 PCIe card or Thunderbridge, connect the Symphony I/O to Port 1 Channels 1-32 port and legacy interfaces (in a supported combination) to the Port 2 Channels 1-64 port.
  • Legacy Apogee interfaces donʼt include Loop clock functionality (as found on Symphony I/O). Thus, when legacy interfaces are connected to a Symphony 64 PCIe card or Thunderbridge, the “Use Loop Sync” checkbox does not appear and Loop sync functionality is defeated on the Symphony I/O. Use one of the clock configurations described on pages 6-7 of the Symphony 64 Userʼs Guide v1.1.

Legacy Interface Supported Combinations

See the Symphony 64 Userʼs Guide v1.1 for connection diagrams

1 to 4 Rosetta 800s
1 to 4 Rosetta 200s
1 AD16X (standard routing) 1 AD16X (advanced routing) 2 AD16X (standard routing) 2 AD16X (advanced routing)

1 DA16X (standard routing) 1 DA16X (advanced routing) 2 DA16X (standard routing) 2 DA16X (advanced routing)

1 AD16X (standard routing) + 1 DA16X (standard routing)
1 AD16X (standard) + 1 DA16X (standard) + 1 AD16X (standard) + 1 DA16X (standard) 1 AD16X (advanced routing) + 1 DA16X (advanced routing)

1 Rosetta 800 + 1 AD16X (standard routing) 1 Rosetta 800 + 1 AD16X (advanced routing) 1 Rosetta 800 + 1 DA16X (standard routing) 1 Rosetta 800 + 1 DA16X (advanced routing)

1 AD16X (standard routing) + 1 Rosetta 800 1 AD16X (advanced routing) + 1 Rosetta 800 1 DA16X (standard routing) + 1 Rosetta 800 1 DA16X (advanced routing) + 1 Rosetta 800

1 AD16X (standard routing) + 1 DA16X (standard routing) + 1 Rosetta 800

When using Apogee interface with Cubase, output volume level goes to max.

Symptom: When opening any Cubase session or selecting Apogee as the audio device, the output goes to full volume every time.

Solution: In Cubase, go to Devices > Device Setup > Control Panel > Core Audio Device Settings. Under Options, verify that set device attenuation to 0 dB is unchecked.

I can’t change the Symphony 64 card source port setting in System Preferences

Symptom: Port Source Setting for Symphony 64 cannot be successfully changed from System Preferences/Sound.

Solution: There is a known issue with changing the Symphony64 card Source setting from 1 port to 2 ports or vice versa can cause “System Preferences/Sound” to hang or “beach ball”

We recommend using Audio MIDI Setup (found in Applications > Utilities > Audio MIDI Setup) to change the Symphony64 card Source for the ports. Always remember to quit all applications and restart the computer after changing the number of ports.

My DA16x in Advanced routing is showing up as an AD16x in Maestro for Symphony64 or Mobile

Symptom: There is a known issue with the current (as of 2012) Symphony installer where after initially connecting and powering up an DA16x in Advanced routing, it sometimes will show up as a AD16x in Maestro2 and Logic…

Solution: Open Maestro2 and highlight the device in the left-hand device column… then go to the “Device Settings” tab and select “DA16x” in the drop-down menu. Quit Maestro and restart the computer. After the computer restarts, launch Maestro and confirm that the DA16x is showing up correctly and then go to both the input and output routing tabs and click “reset routing” in each tab.

My AD16x in Advanced routing is showing up as a DA16x in Maestro for Symphony64 or Mobile

Symptom: There is a known issue with the current (as of 2012) Symphony installer where after initially connecting and powering up an AD16x in Advanced routing, it sometimes will show up as a DA16x in Maestro2 and Logic…

Solution: Open Maestro2 and highlight the device in the left-hand device column… then go to the “Device Settings” tab and select “AD16x” in the drop-down menu. Quit Maestro and restart the computer. After the computer restarts, launch Maestro and confirm that the AD16x is showing up correctly and then go to both the input and output routing tabs and click “reset routing” in each tab.

My AD16x is showing up as a Rosetta in Maestro for Symphony 64 or Mobile

Symptom: There is a known issue with the current Symphony installer (as of 2012) where after initially connecting an AD16x for the 1st time and powering it up, it might show up as a Rosetta 800 in Maestro2, which in turn can make it seem like your channels are limited to 8 in Maestro and Logic…

Solution: Quit Maestro and restart the computer. After the computer restarts, launch Maestro and confirm that the AD16x is showing up correctly. After that, go to the input and output routing tabs in Maestro and click “reset routing” for each tab.