Ensemble

Is Ensemble compatible with Mac OS X El Capitan (10.11)?

Yes! Ensemble Thunderbolt and Ensemble FireWire are both fully compatible* with Mac OS X El Capitan (10.11 to current).  Please be sure to download and install the latest El Capitan compatible software package for your product from Apogee’s site.

*  Although Ensemble FireWire is not “officially supported” after OS X 10.10.5, it is still compatible with OS X 10.11 and should work just like it did on OS X 10.10. You can download the latest installer for Ensemble Firewire and use it on 10.11 even though it says “Mac OS X 10.10 and 10.9 only”.

 

Click to find the latest Ensemble Thunderbolt Software Installer

Click to find the latest Ensemble FireWire Software Installer

 

Are Apogee products compatible with Pro Tools 12?

Yes!  The following products have been tested and are fully compatible with Pro Tools 12 (every version of 12):

  • JAM
  • JAM 96k
  • MiC
  • MiC 96k
  • Groove
  • GiO
  • ONE for Mac (old and new versions)
  • ONE for iPad & Mac
  • Duet FireWire
  • Duet 2
  • Duet for iPad & Mac
  • Quartet for iPad & Mac
  • Ensemble FireWire
  • Ensemble Thunderbolt
  • Symphony I/O (USB, Symphony, and Pro Tools HD modes)
  • Symphony I/O MkII (Thunderbolt and Pro Tools HD)
  • Symphony 64 PCIe
  • Symphony 64 | ThunderBridge
  • X-Symphony equipped X-Series and Rosetta Series Converters
  • X-HD equipped X-Series and Rosetta Series Converters

Signal not showing up where it’s supposed to and routing incorrect in Pro Tools

If your signal isn’t showing up correctly in Pro Tools, coming out of Pro Tools to the desired outputs, or if the routing isn’t showing up as expected, there are a few things to check. Look below for the section that applies to the Apogee product you’re using:

 

JAM, JAM 96k, MiC, MiC 96k, Groove

  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window. If you are using JAM or MiC, you will first need to create a ‘Pro Tools Aggregate I/O’ and then you will select ‘Pro Tools Aggregate I/O’ as your ‘Playback Engine’. Click here for setting up JAM for Pro Tools.  Click here for setting up MiC for Pro Tools.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

 

ONE (every model), GiO, Duet (every model), Quartet, Ensemble (every model)

  • Confirm that you are using the correct inputs/outputs on your device. Click here for instructions on how to setup ONE.  Click here for instructions on how to setup Duet.  Click here for instructions on how to setup Quartet.
  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window.
  • Launch ‘Apogee Maestro’ and click the ‘Reset Routing’ button in both the ‘Input Routing’ and ‘Output Routing’ tabs. If you’re using an Avid Duet or Avid Quartet, you will use ‘Pro Tools I/O Control’ app instead of Maestro. Click here if you need to download the Pro Tools I/O Control app for Avid Duet or Quartet.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

Symphony I/O, Symphony I/O MkII, AD16x, DA16x, Rosetta 200, Rosetta 800

 

 

What is the ‘A button’ (device ID) in Maestro for?

Most Apogee products that use the Apogee Maestro 2 control application will include a ‘Device ID’ button that can be found in multiple Maestro tabs under a graphical icon for the connected Apogee device. You will usually see this button as an ‘A’.

Here is an example of what it looks like when you have a Symphony I/O connected:

img-0

 

The purpose of this button is to quickly identify which Apogee device you’re adjusting parameters in Maestro for. When you click on the button, it will light up the front-panel of the corresponding Apogee device so you can see which device you are adjusting parameters in Maestro for. Click the button again and the device will no longer be identified.

Since multiple Apogee devices can be connected and appear in Maestro at the same time, it can sometimes be confusing to know which device you’re adjusting parameters for. Having more than one Duet or Quartet connected to a Mac may not be as common as having multiple Symphony I/Os or Ensembles connected, but the ‘Device ID’ buttons are there for each product, just in case.

 

A typical use-case:

You have 2 Symphony I/Os connected to one Mac and both are showing up in Apogee Maestro. You can go to the ‘Device Settings’ tab in Maestro and change the peripheral prefix of the 2nd Symphony I/O to ‘B’ (or any other letter you want). Now, when you click the ‘B’ button (Device ID) in Maestro, the 2nd Symphony I/O will become identified.  If you click the ‘A’ button, the 1st Symphony I/O will become identified.

 

Why are the input and output level/volume popup indicators not showing up?

Several Apogee products have pop-up level indicator graphics that will appear on the desktop of your Mac when the input and output levels are adjusted from the device or from the Mac’s keyboard volume buttons.

 

If the pop-ups aren’t appearing, there are a few things to check:

Launch ‘Apogee Maestro 2’ from your Applications folder, click on the ‘Apogee Maestro 2’ drop-down desktop menu and select ‘Preferences’. Confirm that the ‘Display pop-ups’ checkbox is checked. If you don’t see this option, then pop-ups aren’t available for the product you’re using.

 

If you’ve confirmed that the ‘Display pop-ups’ checkbox is checked and you’re still not getting the pop-ups, try the following:

 

– Unplug/replug your Apogee device

– Restart your Mac

– Launch ‘Activity Monitor’ (Applications> Utilities> ‘Activity Monitor’), click the ‘View’ drop-down desktop menu and select ‘All Processes’. Type ‘apogeepopup’ in the searchbar in the upper right-side corner of Activity Monitor. Once you see ‘ApogeePopup’ displayed in the list, highlight it and force-quit the process by clicking the ‘X’ button in the upper left-side corner of Activity Monitor. Wait a few seconds and you should see the popups again after adjusting input/output level.

 

*Note for Duet Firewire and Ensemble Firewire customers*

There was a known issue with pop-ups not working for Duet Firewire and Ensemble Firewire when using any version of Mac OS 10.8. It is recommended that you use either a version of Mac OS earlier than 10.8 or later than 10.9.

 

 

Apogee Maestro crashes when I launch it

If Apogee Maestro 2 is crashing every time you try to launch it, follow the steps below:

 

 

– Quit Apogee Maestro.

– Go to your Applications folder and locate the ‘Apogee Maestro 2’ icon.

– Click once on the icon and then hold down the Command key and press ‘i’ for ‘Get Info’.

– In the ‘Get Info’ window, check the ‘Open in 32-bit mode’ checkbox.

– Close the Get Info window and relaunch Apogee Maestro.

My Apogee’s level meter peaks when play audio from iTunes

It has been documented that if the volume control built into iTunes is all the way up, the signal sent is boosted causing the Apogee interface’s output level meters to peak.

The only way to correct this is to lower the volume slider in iTunes until this doesn’t happen. As a general guide, try setting it around 90% of the maximum level.

How do I find the Maestro software on your website?

The Apogee Maestro 2 software is not on the Apogee website as a separate file. Instead, it is installed with the software package for your Apogee interface.

For example, if you download and install the Duet for iPad & Mac software, Maestro 2 will automatically be installed and placed in your Applications folder.

This is true for any Apogee interface software. You can find the appropriate software for your Apogee interface by going to the support section of our website:

http://www.apogeedigital.com/support